Finally Block Sanding

I have been busy the last few days but I don't have many pictures to show for it.  I cleaned out the barn stall and got it set up as the make-shift bodyshop where I'll be doing all the block sanding.  It would be much easier if I could have compressed air to use while block sanding because it helps keep the dust from clogging up in the sandpaper but as I mentioned before if I try to use the compressor at the barn it throws breakers.  It would also be too difficult to do the block sanding at my house because I would have to set up a table outside each day and then move the parts in and out which would undoubtedly lead to scratches and scuffs, not to mention that if it rained I couldn't work on them.  The doors are so heavy and awkward there is no way to move them without rubbing them against you.  I also cleaned out one side of my garage.  I hauled off a lot of stuff and stored a bunch of stuff.  I had to clear room to have a safe place to store the panels as I finished sanding each one.  Once they have been sanded it is very important they don't get any scratches or nicks.  Also, this weekend is Christmas and it will be much nicer to eat dinner at the dinning room table rather than cram around the kitchen table.

I hated to get rid of them, but I had to take the quarter panel and fender off to the scrapyard.  I tried to get rid of them locally, and I could have sold them if I had the time to advertise them, but I ended up stripping them of all trim and useable parts.  I got $10 for them at the scrapyard and I have already tripled the money I paid for both of them by selling a piece of trim from the quarter panel.  I still have some pieces to sell.  If I had the time and space to store them I would have liked to have cut the quarter, done some body work and practiced painting it and then I would have liked to have hung it on the wall.  The fender was rusted too badly as wasn't useful.  All the panels were curved so I couldn't use it for scrap metal.

After raining on and off the last couple of days, today was the winter solstice, the shortest day of the year, and the weather has turned painfully cold, but at least finally dry.  The last two days have had wind so powerful that it has torn the cover off our gazebo behind the house, blown some shingles off dad's house and one tree down in the back of his yard.  I couldn't even leave the barn door slightly open today because it kept blowing debris inside while I was trying to work.

I went to the Goodwill store and bought a couple of cheap blankets to lay the parts on to prevent scratches and dents.  After hitting the doorjambs with some 320 grit sandpaper I followed them up with some Scotchbrite pads, then flipped the door over and hit it with some guide coat.  Guide coat is a thin layer of black powder or paint that covers the work area.  It gets into the divots, holes and scratches in the paint.  When you begin sanding you sand until all the black is gone and that is when you know the area is sufficiently smooth.

After applying a layer of guide coat I begin with some 180 grit sandpaper wrapped around a foam soft block pad from the 3M company.  The bodyshop recommended soft blocking this car.  They said in this particular instance it would result in a better job than using a hardblock, or non-flexible sanding block.  After removing all the guide coat with 180 grit sandpaper I apply another layer of guide coat and then come back with the same process, this time using 320 grit sandpaper.  It is a time consuming process, but it is not as physically demanding as stripping the paint.  For that reason, I actually find this step somewhat enjoyable.  It's nice to actually see progress being made, to see the finish become smooth and to actually reach the end of a goal as each panel is finished and set aside.  I finished this door today which means I won't have to do any work with it until it comes back from being painted.

One thing about this project: The little tabs that stick up from the side panels and hold the clips for the woodgrain molding have been a massive pain this entire project.  They make each and every step of bodywork quite literally 4 times more difficult and time consuming.  This last step would almost seem easy compared to having to sand around them, making sure to blend the sanding out evenly in all directions to maintain smooth bodywork.  I really, really, really hate these tabs.

Painting Some Engine Parts

The rest of the parts are now back from being primered.  I went and picked them up with dad's smaller enclosed trailer.  The hood was almost too wide for that trailer, though I wouldn't have thought that initially.  It had about an inch to spare on both sides.  At the body shop Gary recommended using Sunmite sandpaper for dry sanding.  It turns out Sandmite paper costs less than half of the 3M brand paper and doesn't clog up with dust as bad.  I've ordered some but it won't be here until Thursday.  That leaves me time to get to a lot of the things I haven't had time to work on so far, like painting the various engine parts that I blasted at Larry's a couple months ago.  Fortunately I have kept them stored and dry so rusting isn't an issue.  

First I installed this heater hose outlet that I had to order from the internet.  This part is a Pontiac specific piece and cost $25 dollars.  I think that is pretty ridiculous, but if I look at it from another perspective, mine was completely rusted so I'm glad, at least, that it is still available.  The piece is a press fit so I was worried I might damage it while attempting to install it.  I used a large socket, rag and a hammer and though it didn't go in easy, it eventually seated and went right into place with no problem. 

Daniel's dad gave me this still-new-in-the-package oil cap.  I'm thankful he did because I think it really dresses up the valve cover and makes it look a lot better.

And here's a picture of the engine after I took the masking paper off the exhaust manifolds.

I started out by taking each part and cleaning it with brake parts cleaner to prepare it for primer and paint.  Brake parts cleaner is some of the best stuff to use for cleaning and prepping parts for paint but it evaporates very quickly and must be wiped off or it will leave and invisible residue that will cause the primer and paint to not stick.

After cleaning each piece thoroughly I primered one side of them all, let them dry, flipped them and primered the other side.  Even though it is December I have been fortunate to have a very mild winter this year.  It was almost in the 60s today and with the parts sitting in the sun combined with the constant breeze, along with very little humidity, the parts dried quickly.  After primering both sides I came back with high gloss black paint.  I actually forgot that the pulleys were supposed to be blue like the engine but after I  had one of them painted black I decided I didn't mind them being that color so I decided to leave it.  It may not be original but in this particular instance that doesn't bother me.  If it does in the future, they are pretty easy to remove, so I'll just take them off and repaint them.

Except on the lone piece that received "Dull Aluminum" paint.

In between drying time I cleaned the garage and also did a few more things on the engine.  I painted the letters and numbers on the timing bracket to make it easier to see.  I forgot to take a picture before I started so for the before picture you'll have to pretend the "4" isn't white.

Here's the after.  As many people do, I always do this on all engines now.  It really improves visibility when trying to use a timing light.

I always use finger nail polish that I get at the Dollar Store for marking the timing indicators.  It sells for $1.00 and I've had good luck with the Xtreme Wear brand being pretty durable.

After the sun began to go down and the day started to get cooler I brought all the parts inside.  I like to pick them up off the box one at a time so the paint doesn't stick to the box.  If it does, when you separate the paint from the box it will either remove the paint or leave a piece of torn cardboard to the part, which won't come off.

I had taken the motors that operate the rear tailgate and rear window to a local electric shop here in town.  Dad went with me because he had known the owner for many years and when dad used to work at a dealership here in town back in the 70's he would let the owner sell some of their wholesale cars.  I think typically they work on only large scale, industrial motors but he fixed both of these and it was actually cheaper than buying a used one and having it shipped.  He even repainted the cases.  These motors had pretty bad water damage from the windows leaking on them over the years.  I was also glad to have them work on them because I like to support local, family owned businesses whenever possible.

Rain Delay

The weather has not been very cooperative.  I finished sanding and preparing the body of the car and all I had left to do was to sand the hood and I could take the car to be primered, but the day I was going to work on the hood it decided to start to rain... for five days straight.  After the 40 days and nights of flooding I was finally able to start on the hood, but the temperature dropped back down into the 20s at night and the days were sometimes only up to the 40s.  I was, in a strange way, actually looking forward to working on the hood.  I knew it meant I was almost done with this leg of the job.  I would be able to sit it on saw horses so I could finally work on something in a decent position that didn't hurt my back.  I was wrong.  The paint on the hood was extremely difficult.  My best guess as to why, as my dad had said could possibly be a reason, is that perhaps the heat from the engine had baked the paint on over the years.  My sand blaster was completely ineffective.  It took two entire blaster-jugs full of sand to do an area about 12x12 inches.  I knew that would take days and cost a fortune in sand.  You could hold the blaster on the paint and for the first second it didn't do anything, and then it would finally remove one small spot.  I ended up having to sand the entire hood by hand or with the DA grinder.  When I came to a spot that had a pit and needed blasting I would take a piece of green tape and put on the hood to mark the spot I needed to come back to.  This took two full days.

It seems everyone around me has been sick.  It has been going around this area in a bad way.  Some entire counties have even closed schools due to the flu and strep throat.  I started to feel sick and I was very scared that I might be coming down with one of the two.  I started cramming as much vitamin C as I could.  Yesterday I headed over to dad's house as early as I could stand, feeling pretty miserable, and finished the hood and then dad helped me load the car up and I took it up to the body shop.  They had a somewhat narrow time frame to fit me in and the rain had already caused a delay so I didn't have time to take a sick day.  Despite feeling pretty run down I got it done.

Today I woke up feeling better than I have the last two days.  I headed up to the body shop first thing.  I took the vacuum to clean up a lot of the left over sand and plenty of other supplies to get the car ready for primer.  The sand blaster had damaged some of the tape and paper I had sealed the open spaces with so those areas had to be repaired.  I can handle cleaning a little bit of sand out of the carpet but I certainly don't want primer colored spots on the seats.

There is a hill leading up to the door to the paint booth.  I backed up to the door as far as I could before the back of the trailer would bottom out on the gravely hill side.  This left about a foot between the concrete floor entrance of the paint booth and where the door to the trailer opened to.  We had to push the car uphill to get it into the paint booth.  There were four of us pushing and it was literally all we could do to get it into the shop; The car is that heavy, even without the engine, glass, doors or front clip.  We would have to push the car a few feet and then chock the tire and take a breath.   

After having spent a total of almost a week on the rear driver side door I admitted defeat and let Gary work his magic with it.  If you don't account for body-filler dry time, it only took him about an hour.  I was glad and also disgusted at the same time.  That's why he's the professional.  This shop has built plenty of show cars, one of which sold to Jay Leno at one of the Barrett-Jackson Collector Car auctions.

While he was at it he fixed one more very small spot that I hadn't gotten to.  I snagged this picture of him in action.

Here's a picture of the hood.  All I have left is to take some sand paper and smooth the individual holes in the vented portion of the hood.  I didn't have enough sand to finish each vent hole individually so I'm going to have to finish that up by hand.  This is a very, very large hood.

Here she is all taped up and ready to go.  Almost...

There was one other spot I ended up addressing and that caused me to not finish up today so I'm going to head back up very early tomorrow and finish up, then I can wipe the car down with wax and grease remover and it should be ready to spray.  After that I'll come pick the car up and I will prep the rest of the parts since there isn't room to do the body and the other parts all at the same time.

The HEI distributor came in today.  I was pointed to the company I bought it from while searching the internet. Here is basically why I bought this distributor:  Name brand companies like Summit and Jegs have started selling items made in China by slapping their name on them and still selling them at mark-up prices.  Though these Chinese companies have high quality control they still are made cheaper than their domestic counterparts.  The company I used, Skip White Performance, uses the same quality products made in China, however they charge a fraction of the price.  I got this unit for $53 shipped.  The cost of the other products, which are of the same quality, is between $150 and $200.  I was scared by the low cost and did a lot of research on this product and the company.  I even viewed a dissection of one of these distributors and the machining and assembly is as good of quality as you can expect from a name brand. 

I previously ordered a kit that I had believed would allow me to use my original distributor shaft and just install new components to change it over to HEI.  I later learned that I was incorrect and what I ordered was only an update kit for older distributors that had originally come with the old style, factory HEI.  This kit alone cost 2/3 more than what I paid for this whole distributor and I still would have had to source my own HEI distributor shaft.  I'm going to be sending the kit back.

A little bodywork and April's Pregnant

Today was December 3rd and it was 75 degrees.  It felt absolutely amazing outside.  If the government could find a way to tax great weather I wouldn't have been able to afford today.  As tempting as it was to head off on the motorcycle I knew I have to use this time to get stuff done while the weather is nice.  I called the bodyshop and he said he hopes he can get me in at the beginning of next week.

The driver side rear quarter has a little bit of pitting so I headed over early and laid down a layer of bondo.  I always try to lay it thinn but every time it turns out thicker than I intend.  I think I have a fear of putting too little then having to come back again.

After I laid some bondo I used the dry time to go get some supplies.  I'd like to point out again that sand paper has become ridiculously expensive.  I also took the time, though I was eager to make progress on The Clam, to wash The '57 so I could cover and tarp it for the winter.

Then I moved on to the tailgate storage compartment.  I wanted to go ahead and get some primer on the tracks that the tailgate rides on.  These were bare metal after I blasted them and I'm afraid the primer the bodyshop will apply would be too thick and possibly cause binding.  Also, I since I can't get inside the area to sand them again I wanted them protected as soon as possible so they didn't rust.  Before that, I had to wipe down the entire area, including inside the tracks, with grease and wax remover to prep it for paint, but before I could do that I had to get all the sand out of there.  This picture shows just a small fraction of how much sand was trapped in this compartment.

After scooping out as much as possible I used the vacuum to get the rest.  This vacuum cleaner is ancient but as with most things that were made long ago it still works great and has lasted forever.

I started with the tailgate support arm up so I could get behind the track and the mounting plates that attach to the tailgate.  I also sprayed the surrounding areas just in case there were some areas of bare metal that may have blended in and I missed.  This pan is actually unlevel which allows the water to run to the passenger side and drain out through the holes you can barely see under the track in the first picture.  If you recall, this entire area was clogged with compacted dirt, rocks... and a shotgun shell.  After the car is painted I will apply a liberal coat of grease to the inside of these tracks.

I didn't get completely finished today.  Here is where I stopped.  There was a large dent with no creases in the rear quarter when I got the car.  I was glad when I first took the taillight out that I was able to run my hand inside and most of the dent simply pushed back out.  There was, however, a smaller area in the rear that remained.  It could probably be straightened back out with the right tools through the taillight housing, but I don't have any of those tools.

Tomorrow I'll finish the bodywork on the driver side, then start to finish the final prep on the roof.  If I can finish that I'll move on to the remainder of the rear quarters.  Here is the passenger side.  This side had some pretty intense glue on the rear quarter so I had to sandblast it all off.  Any attempts to sand it with paper simply clogged the paper almost immediately. 

By this time I had to get going.  April was leaving her doctor's appointment where we found out definitely that she is pregnant, so we went out to eat with my mother and father to tell them.

Got one in the oven